MATRIC • FSC • NTS • ETEA • CSS • PMS etc MCQs Learn, Practice, Prepare, Succeed! Prepare Today, Succeed Tomorrow!

Q: What is setting out in construction?

A) Transferring the dimensions and positions shown on drawings onto the ground

B) Testing concrete cubes

C) Removing soil from a foundation

D) Applying waterproofing

Q: What is a total station?

A) To compact soil

B) To test concrete strength

C) To measure cement fineness

D) To electronically measure angles and distances and assist in coordinate determination

Q: What is the main function of an accelerating admixture?

A) To reduce cement hydration

B) To increase setting time

C) To speed up setting or early strength development

D) To increase soil permeability

Q: What is the main purpose of a site survey before setting out a building?

A) To determine worker salaries

B) To establish accurate positions, dimensions and levels from design information

C) To test concrete strength

D) To select wall paint

Q: What is a traverse in surveying?

A) A single contour line

B) A soil classification method

C) A concrete foundation

D) A series of connected survey lines whose lengths and directions are measured

Q: Which soil is most likely to experience significant consolidation settlement?

A) Soft saturated clay

B) Dense gravel

C) Hard rock

D) Coarse sand

Q: What is the main responsibility of a civil engineer during construction?

A) To perform only administrative tasks

B) To purchase all materials personally

C) To ensure work is executed according to approved designs, specifications, quality requirements and applicable procedures

D) To operate every construction machine

Q: What is the main purpose of road geometric design?

A) To provide a safe, efficient and comfortable roadway

B) To eliminate drainage

C) To reduce visibility

D) To maximize pavement thickness without analysis

Q: What is BOD in environmental engineering?

A) Basic Oxygen Density

B) Bacterial Organic Drainage

C) Biochemical Oxygen Demand

D) Biological Oxide Difference

Q: Which type of retaining wall relies significantly on its own weight for stability?

A) Cantilever retaining wall

B) Counterfort wall only

C) Sheet pile wall only

D) Gravity retaining wall

Q: What is the main purpose of a project specification?

A) To replace all drawings

B) To define technical requirements, materials, workmanship and standards

C) To list only worker names

D) To record daily weather only

Q: What is the purpose of chlorination in water treatment?

A) To disinfect water and control pathogenic microorganisms

B) To remove all hardness

C) To increase suspended solids

D) To increase turbidity

Q: What is a friction pile?

A) A pile with no contact with soil

B) A pile used only as a column

C) A pile that obtains significant resistance through skin friction along its shaft

D) A pile used only for retaining water

Q: What is the primary stability concern for a retaining wall?

A) Sliding, overturning and bearing failure

B) Paint failure only

C) Roof leakage

D) Concrete color

Q: What is the main purpose of low heat cement?

A) To eliminate curing

B) To reduce heat generation during hydration

C) To increase aggregate size

D) To increase setting temperature

Q: What is a foresight in levelling?

A) The first reading on a benchmark

B) A staff reading generally taken on a point whose elevation is to be determined before moving the instrument

C) A horizontal angle

D) A chain measurement

Q: What is the main purpose of water in a concrete mix?

A) To cause hydration and provide necessary workability

B) Only to cool aggregate

C) To prevent setting

D) To replace cement

Q: What is superelevation on a highway?

A) Raising the outer edge of a pavement on a horizontal curve

B) Adding a drainage channel

C) Increasing pavement width at a straight section

D) Lowering the entire pavement below ground

Q: What is the characteristic compressive strength of concrete commonly assessed at?

A) 7 days

B) 14 days

C) 28 days

D) 3 days

Q: What does fineness modulus generally indicate for aggregate?

A) Aggregate crushing strength

B) Specific gravity of cement

C) Aggregate moisture content

D) Average particle size distribution